Search
| 1 | bit | 比特,位,PLC数据基本单位,经常用b表示。 |
| 2 | Byte | 字节,包含连续的8个位,经常用B表示。 |
| 3 | Word | 字,包含两个字节,经常用W表示。 |
| 4 | DWord(double word) | 双字,包含两个字,经常用DW表示。 |
| 5 | bool | 布尔型数据,即位数据。 |
| 6 | Int | integer整数,-32768~+32767之间的所有整数(数学上的)。 |
| 7 | Dint | double integer,双整数,-2147483648~+2147483647之间的所有整数(数学上的)。 |
| 8 | real | 也叫float,实数,浮点数, -3.402823e+38~-1.175 495e-38 ,+1.175 495e-38 ~+3.402823e+38。 |
| 9 | not | 非,取反。 |
| 10 | P | positive正的。 |
| 11 | N | negative 负的。 |
| 12 | I | Immediate 立即的。 |
| 13 | S | set 置位,使…为1,并保持。 |
| 14 | R | reset 复位,使…为0. |
| 15 | NOP | 空操作。 |
| 16 | Read | 读取。 |
| 17 | Write | 写入。 |
| 18 | RTC | Real time clock实时时钟,即年月日日期和小时分秒星期时间的统称。 |
| 19 | D | double integer 双整数。 |
| 20 | Round | 四舍五入。 |
| 21 | Trunc | 取整;截断;截取;整数部分;截断取整。 |
| 22 | Count | 计数 |
| 23 | Up | 向上 |
| 24 | Down | 向下 |
| 25 | HSC | high speed counter 高速计数器 |
| 26 | Add | 加法 |
| 27 | Sub | subtraction 减法 |
| 28 | Mul | multiplication 乘法 |
| 29 | Div | division 除法 |
| 30 | Inc | increase 增加 |
| 31 | Dec | decrease 减少 |
| 32 | En | enable 使能,允许。 |
| 33 | I | interrupt 中断,打断 |
| 34 | Ret | return 返回 |
| 35 | Atch | 连接指令 |
| 36 | CLR | clear清除 |
| 37 | EVNT | event事件 |
| 38 | INV | Invert 反转,取反 |
| 39 | And | 与操作 |
| 40 | Or | 或操作 |
| 41 | Move | 移动,传送 |
| 42 | BLKMOV | block move 块传送 |
| 43 | JMP | jump 跳转 |
| 44 | LBL | lable 标签 |
| 45 | SCR | sequence control relay 顺序控制继电器 |
| 46 | SCRT | sequence control relay transformation 转换指令 |
| 47 | SCRE | sequence control relay end 结束指令 |
| 48 | END | 结束 |
| 49 | STOP | 停止 |
| 50 | SHL | shift left 左移指令 |
| 51 | SHR | shift right 右移指令 |
| 52 | ROL | rotate left 左循环指令 |
| 53 | ROR | rotate right 右循环指令 |
| 54 | TON | timer-on 延时接通指令 |
| 55 | TOF | timer-off 延时断开指令 |
| 56 | TONR | timer-on- remember 保持型延时接通定时器 |
| 57 | SBR | subroutine 子程序 |